Control of the resistive switching voltage and reduction of the high-resistive-state current of zinc oxide by self-assembled monolayers.

We investigated the effect of self-assembled monolayer (SAM) modification of ZnO on the resistive switching behaviour by fabricating electrode-sandwiched devices (ITO/ZnO-SAM/Al). The resistive switching voltages of SAM-modified ZnO films were shifted from that of bare ZnO depending on the surface dipole induced by the SAMs. In particular, methylaminopropyl-substituted SAM-modified ZnO showed lower switching voltage (1.6 V) than bare ZnO (2.9 V). Moreover, the on/off ratio was also improved by SAM modification (from 102 to 104).

Bioactive properties and organosulfur compounds profiling of newly developed garlic varieties of Bangladesh.

Studies are being carried out on achieving the maximum quality of garlic through various approaches. In Bangladesh, new garlic varieties (BARI 1-4, BAU-1, BAU-2, BAU-5) have been recently developed by artificial selection to enhance their quality. The present study aimed to evaluate their potency in terms of bioactive properties and organosulfur compounds content using different bioassay and GC-MS techniques while comparing them with other accessible varieties (Chinese, Indian, Local). The new variety, BARI-3 showed the highest antioxidant activity and total phenolic content. It was also found with the highest level of a potent blood pressure-lowering agent, 2-vinyl-4H-1,3-dithiine (78.15 %), which is never reported in any garlic at this percentage. However, the local variety exhibited greater inhibitory properties against the tested organisms including multidrug-resistant pathogens compared to other varieties. This study primarily shows the potential of these two kinds of garlic for their further utilization and development.

Molecular detection of Babesia and Theileria from crossbred cattle in Sirajganj and Rangpur districts of Bangladesh.

BACKGROUND: Babesia and Theileria are potential threats to the livestock industry, causing considerable economic losses. These tick-borne blood parasites are more prevalent in crossbred cattle than local cattle in Bangladesh. OBJECTIVES: To confirm the species of Babesia and Theileria in crossbred cattle from the northern part of Bangladesh using conventional and molecular tools. METHODS: A total of 385 crossbred cattle blood samples were subjected to DNA extraction and PCR. For molecular detection, B. bigemina rhoptry-associated protein 1a, B. bovis spherical body protein-4, and Theileria spp. 18S rRNA were used as the marker genes. RESULTS: Using PCR, only 72 (18.7%) samples were found piroplasm positive, of which 12.2% Theileria, 4.7% Babesia, and 1.8% mixed infections. Both Babesia (7.3%), Theileria (7.7%) and mixed (2.8%) infections were detected in Sirajganj, and only Theileria (20.4%) was detected in Rangpur district. By PCR and nPCR we detected B. bigemina and T. annulata in Sirajganj district, and Theileria sp. in Rangpur district. The target gene sequences of isolated pathogens confirmed B. bigemina and T. annulata, and Theileria sp from these samples. Blood smears of all samples were also examined microscopically for Babesia and/or Theileria spp. and 14.3% of samples were found positive, of which 5.9% Babesia and 8.3% Theileria. Generally, the pathogens detected in Sirajgang and Rangpur were genetically related to South Asia, particularly South East Asian isolates. CONCLUSIONS: These findings provide information for a better understanding of the epidemiology of Babesia and Theileria as well as to improve the approaches for diagnosis and control of tick-borne diseases in Bangladesh.

Mammalian and Avian Larval Schistosomatids in Bangladesh: Molecular Characterization, Epidemiology, Molluscan Vectors, and Occurrence of Human Cercarial Dermatitis.

Schistosomiasis is a neglected tropical disease (NTD) caused by blood flukes (Schistosoma spp.). Schistosomatids affect a wide array of vertebrate hosts, including humans. In the present study, multiple species of schistosomatids were identified by isolating schistosomatid cercariae (SC) from naturally infected snails. We also described different biotic and abiotic factors influencing SC infections in snails and reported human cercarial dermatitis (HCD) for the first time in Bangladesh. A total of 22,012 snails of seven species: Lymnaea auricularia, L. luteola, Indoplanorbis exustus, Physa acuta, Viviparus bengalensis, Brotia spp., and Thiara spp., were collected and examined. Among these snails, 581 (2.6%) belonging to five species: L. luteola, L. auricularia, P. acuta, I. exustus, and V. bengalensis, were infected with SC. The rate of infection was the highest for L. luteola (11.1%), followed by L. auricularia (5.3%), and was the lowest for V. bengalensis (0.4%). Prevalence in snails was the highest in September (16.8%), followed by October (9.5%) and November (8.8%), and was the lowest in colder months, such as January (1.8%) and February (2.1%). Infections with schistosomatids were more common in larger snails and snails collected from sunny areas. We confirmed the presence of Schistosoma indicum, S. incognitum, S. nasale, S. spindale, and Trichobilharzia szidati by PCR and sequencing. Through a questionnaire survey, we detected HCD in 214 (53.5%) individuals, and the infection rate was almost equally distributed across all professions. Collectively, the present results suggest that lymnaeid snails are the main vector for Schistosoma spp. prevalent in Bangladesh, and schistosomatids with zoonotic potential are also prevalent.

Investigation of Morphological, Optical, and Dielectric Properties of RF Sputtered WOx Thin Films for Optoelectronic Applications.

Tungsten oxide (WOx) thin films were synthesized through the RF magnetron sputtering method by varying the sputtering power from 30 W to 80 W. Different investigations have been conducted to evaluate the variation in different morphological, optical, and dielectric properties with the sputtering power and prove the possibility of using WOx in optoelectronic applications. An Energy Dispersive X-ray (EDX), stylus profilometer, and atomic force microscope (AFM) have been used to investigate the dependency of morphological properties on sputtering power. Transmittance, absorbance, and reflectance of the films, investigated by Ultraviolet-Visible (UV-Vis) spectroscopy, have allowed for further determination of some necessary parameters, such as absorption coefficient, penetration depth, optical band energy gap, refractive index, extinction coefficient, dielectric parameters, a few types of loss parameters, etc. Variations in these parameters with the incident light spectrum have been closely analyzed. Some important parameters such as transmittance (above 80%), optical band energy gap (~3.7 eV), and refractive index (~2) ensure that as-grown WOx films can be used in some optoelectronic applications, mainly in photovoltaic research. Furthermore, strong dependencies of all evaluated parameters on the sputtering power were found, which are to be of great use for developing the films with the required properties.

Electro-spray deposited TiO2 bilayer films and their recyclable photocatalytic self-cleaning strategy.

Recyclable titanium dioxide (TiO2)-based photocatalytic self-cleaning films (SCFs) having a bilayer structure were prepared and assessed. These SCFs comprised two layers of fibers fabricated using an electrospinning process. The self-cleaning layer was made of acrylonitrile-butadiene-styrene (ABS) fibers with embedded TiO2 while the substrate layer was composed of fibers made by simultaneously electrospinning poly (vinyl alcohol) (PVA) and ABS. This substrate improved the mechanical strength of the SCF and provided greater adhesion due to the presence of the PVA. The experimental results showed that the hydrophobicity (as assessed by the water contact angle), photocatalytic properties and self-cleaning efficiency of the SCF were all enhanced with increasing TiO2 content in the ABS/TiO2 fibers. In addition, the introduction of the substrate layer allowed the SCFs to be applied to various surfaces and then peeled off when desired. The ABS fibers effectively improved the strength of the overall film, while deterioration of the ABS upon exposure to UV light was alleviated by the addition of TiO2. These SCFs can potentially be recycled after use in various environments, and therefore have applications in the fields of environmental protection and medical science.

Investigation of Degradation Mechanism of Y6-Based Inverted Organic Solar Cells and Their Utilization in Durable Near-Infrared Photodetection.

The device durability of inverted organic solar cells (OSCs) is investigated based on Y6, which is an effective nonfullerene acceptor for high-performance OSCs. The durability of Y6-based inverted OSCs is poor and it can be caused by aggregation of Y6 in the bulk-heterojunction layer due to heating by continuous photo-irradiation (≈65 °C, 100 mW cm-2 , and 72 h). It is found that the aggregation of Y6 is suppressed at a low temperature (≈50 °C), and that the Y6-based devices can be useful as a photodurable near-infrared detector upon continuous laser irradiation.

Local Cross-Coupling Activity of Azide-Hexa(ethylene glycol)-Terminated Self-Assembled Monolayers Investigated by Atomic Force Microscopy.

Azide-oligo(ethylene glycol)-terminated self-assembled monolayers (N3-OEG-SAMs) are promising interfacial structures for surface functionalization. Its many potential applications include chemical/bio-sensing and construction of surface models owing to its cross-coupling activity that originates from the azide group and oligo(ethylene glycol) (OEG) units for non-specific adsorption resistance. However, there are only a few studies and limited information, particularly on the molecular-scale structures and local cross-coupling activities of N3-OEG-SAMs, which are vital to understanding its surface properties and interfacial molecular design. In this study, molecular-scale surface structures and cross-coupling activity of azide-hexa(ethylene glycol)-terminated SAMs (N3-EG6-SAMs) were investigated using frequency modulation atomic force microscopy (FM-AFM) in liquid. The N3-EG6-SAMs were prepared on Au(111) substrates through the self-assembly of 11-azido-hexa(ethylene glycol)-undecane-1-thiol (N3-EG6-C11-HS) molecules obtained from a liquid phase. Subnanometer-resolution surface structures were visualized in an aqueous solution using a laboratory-built FM-AFM instrument. The results show a well-ordered molecular arrangement in the N3-EG6-SAM and its clean surfaces originating from the adsorption resistance property of the terminal EG6 units. Surface functionalization by the cross-coupling reaction of copper(I)-catalyzed azide-alkyne cycloaddition was observed, indicating a structural change in the form of fluctuating structures and island-shaped structures depending on the concentration of the alkyne molecules. The FM-AFM imaging enabled to provide information on the relationship between the surface structures and cross-coupling activity. These findings provide molecular-scale information on the functionalization of the N3-EG6-SAMs, which is helpful for the interfacial molecular design based on alkanethiol SAMs in many applications.

Paste Aging Spontaneously Tunes TiO2 Nanoparticles into Reproducible Electrosprayed Photoelectrodes.

In this study, the spontaneous microstructure tuning of TiO2 was observed by aging the ethanol/water TiO2 paste for up to 20 days at ambient conditions. A dynamic light scattering study reveals that it formed the outstanding reproducible TiO2 microstructure with a ∼200 nm average particle size and stabilizes in 6 to 20 days under an ambient atmosphere. Interestingly, the as-deposited day 15 sample spontaneously changed its crystallinity upon keeping the paste at ambient conditions; meanwhile the day 0 sample showed an amorphous structure. A dense, uniform, and stable TiO2 electrode was cast on a fluorine doped-tin oxide substrate using the electrospray technique. We exploit the spontaneous evolution of the TiO2 nanopowder to revisit the fabrication procedure of the TiO2 photoelectrode for dye-sensitized solar cells (DSSCs). The controlled microstructure TiO2 film was used in DSSCs, which, to the best of our knowledge, achieved the highest power conversion efficiency of 9.65% using N719 dye in sensitizing the TiO2 photoanode.

Muntingia calabura Leaves Mediated Green Synthesis of CuO Nanorods: Exploiting Phytochemicals for Unique Morphology.

In this study, phytochemical assisted nanoparticle synthesis was performed using Muntingia calabura leaf extracts to produce copper oxide nanoparticles (CuO NPs) with interesting morphology. Scanning electron microscope (SEM) and transmission electron microscope (TEM) analysis of the biosynthesized CuO NPs reveal formation of distinct, homogeneous, and uniform sized CuO nanorods structure with thickness and length of around 23 nm and 79 nm, respectively. Based on Fourier-transform infrared (FTIR) analysis, the unique combinations of secondary metabolites such as flavonoid and polyphenols in the plant extract are deduced to be effective capping agents to produce nanoparticles with unique morphologies similar to conventional chemical synthesis. X-ray diffraction (XRD) analysis verified the monoclinical, crystalline structure of the CuO NPs. The phase purity and chemical identity of the product was consolidated via X-Ray photoelectron spectroscopy (XPS) and Raman spectroscopic data which indicate the formation of a single phase CuO without the presence of other impurities. The direct and indirect optical band gap energies of the CuO nanorods were recorded to be 3.65 eV and 1.42 eV.

Impact of Ar Flow Rates on Micro-Structural Properties of WS2 Thin Film by RF Magnetron Sputtering.

Tungsten disulfide (WS2) thin films were deposited on soda-lime glass (SLG) substrates using radio frequency (RF) magnetron sputtering at different Ar flow rates (3 to 7 sccm). The effect of Ar flow rates on the structural, morphology, and electrical properties of the WS2 thin films was investigated thoroughly. Structural analysis exhibited that all the as-grown films showed the highest peak at (101) plane corresponds to rhombohedral phase. The crystalline size of the film ranged from 11.2 to 35.6 nm, while dislocation density ranged from 7.8 × 1014 to 26.29 × 1015 lines/m2. All these findings indicate that as-grown WS2 films are induced with various degrees of defects, which were visible in the FESEM images. FESEM images also identified the distorted crystallographic structure for all the films except the film deposited at 5 sccm of Ar gas flow rate. EDX analysis found that all the films were having a sulfur deficit and suggested that WS2 thin film bears edge defects in its structure. Further, electrical analysis confirms that tailoring of structural defects in WS2 thin film can be possible by the varying Ar gas flow rates. All these findings articulate that Ar gas flow rate is one of the important process parameters in RF magnetron sputtering that could affect the morphology, electrical properties, and structural properties of WS2 thin film. Finally, the simulation study validates the experimental results and encourages the use of WS2 as a buffer layer of CdTe-based solar cells.

Defect Study and Modelling of SnX3-Based Perovskite Solar Cells with SCAPS-1D.

Recent achievements, based on lead (Pb) halide perovskites, have prompted comprehensive research on low-cost photovoltaics, in order to avoid the major challenges that arise in this respect: Stability and toxicity. In this study, device modelling of lead (Pb)-free perovskite solar cells has been carried out considering methyl ammonium tin bromide (CH3NH3SnBr3) as perovskite absorber layer. The perovskite structure has been justified theoretically by Goldschmidt tolerance factor and the octahedral factor. Numerical modelling tools were used to investigate the effects of amphoteric defect and interface defect states on the photovoltaic parameters of CH3NH3SnBr3-based perovskite solar cell. The study identifies the density of defect tolerance in the absorber layer, and that both the interfaces are 1015 cm-3, and 1014 cm-3, respectively. Furthermore, the simulation evaluates the influences of metal work function, uniform donor density in the electron transport layer and the impact of series resistance on the photovoltaic parameters of proposed n-TiO2/i-CH3NH3SnBr3/p-NiO solar cell. Considering all the optimization parameters, CH3NH3SnBr3-based perovskite solar cell exhibits the highest efficiency of 21.66% with the Voc of 0.80 V, Jsc of 31.88 mA/cm2 and Fill Factor of 84.89%. These results divulge the development of environmentally friendly methyl ammonium tin bromide perovskite solar cell.

Spray Pyrolyzed TiO2 Embedded Multi-Layer Front Contact Design for High-Efficiency Perovskite Solar Cells.

The photovoltaic performance of perovskite solar cells (PSCs) can be improved by utilizing efficient front contact. However, it has always been a significant challenge for fabricating high-quality, scalable, controllable, and cost-effective front contact. This study proposes a realistic multi-layer front contact design to realize efficient single-junction PSCs and perovskite/perovskite tandem solar cells (TSCs). As a critical part of the front contact, we prepared a highly compact titanium oxide (TiO2) film by industrially viable Spray Pyrolysis Deposition (SPD), which acts as a potential electron transport layer (ETL) for the fabrication of PSCs. Optimization and reproducibility of the TiO2 ETL were discreetly investigated while fabricating a set of planar PSCs. As the front contact has a significant influence on the optoelectronic properties of PSCs, hence, we investigated the optics and electrical effects of PSCs by three-dimensional (3D) finite-difference time-domain (FDTD) and finite element method (FEM) rigorous simulations. The investigation allows us to compare experimental results with the outcome from simulations. Furthermore, an optimized single-junction PSC is designed to enhance the energy conversion efficiency (ECE) by > 30% compared to the planar reference PSC. Finally, the study has been progressed to the realization of all-perovskite TSC that can reach the ECE, exceeding 30%. Detailed guidance for the completion of high-performance PSCs is provided.

Selective Extraction of Nonfullerene Acceptors from Bulk-Heterojunction Layer in Organic Solar Cells for Detailed Analysis of Microstructure.

Detailed analyses of the microstructures of bulk-heterojunction (BHJ) layers are important for the development of high-performance photovoltaic organic solar cells (OSCs). However, analytical methods for BHJ layer microstructures are limited because BHJ films are composed of a complex mixture of donor and acceptor materials. In our previous study on the microstructure of a BHJ film composed of donor polymers and fullerene-based acceptors, we analyzed donor polymer-only films after selectively extracting fullerene-based acceptors from the film by atomic force microscopy (AFM). Not only was AFM suitable for a clear analysis of the morphology of the donor polymers in the BHJ film, but it also allowed us to approximate the acceptor morphology by analyzing the pores in the extracted films. Herein we report a method for the selective extraction of nonfullerene acceptors (NFAs) from a BHJ layer in OSCs and provide a detailed analysis of the remaining BHJ films based upon AFM. We found that butyl glycidyl ether is an effective solvent to extract NFAs from BHJ films without damaging the donor polymer films. By using the selective extraction method, the morphologies of NFA-free BHJ films fabricated under various conditions were studied in detail. The results may be useful for the optimization of BHJ film structures composed of NFAs and donor polymers.

Ionic Liquid-Assisted MAPbI3 Nanoparticle-Seeded Growth for Efficient and Stable Perovskite Solar Cells.

With the rapid improvement of perovskite solar cells (PSCs), long-life operational stability has become a major requirement for their commercialization. In this work, we devised a pristine cesium-formamidinium-methylammonium (termed as CsFAMA) triple-cation-based perovskite precursor solution into the ionic liquid (IL)-assisted MAPbI3 nanoparticles (NPs) through a seeded growth approach in which the host IL-assisted MAPbI3 NPs remarkably promote high-quality perovskite films with large single-crystal domains, enhancing the device performance and stability. The power conversion efficiency (PCE) of the MAPbI3 NP-seeded growth of MAPbI3 NPs/CsFAMA-based PSCs is as high as 19.44%, which is superior to those of MAPbI3 NPs and pristine CsFAMA films as the photoactive layer (9.52 and 17.33%, respectively). The long-term light-soaking and moisture stability of IL-aided MAPbI3 NPs/CsFAMA-based devices (non-encapsulated) remain above 90 and 80%, respectively, of their initial output after 2 h of light illumination (1 sun) and 6000 h storage at ambient with a relative humidity range of 30-40%. The use of the IL-assisted MAPbI3 NP-seeded growth for PSCs is a significant step toward developing stable and reliable perovskite photovoltaic devices.

Naphthalene diimide-incorporated helical thienoacene: a helical molecule with high electron mobility, good solubility, and thermally stable solid phase.

A Naphthalene diimide (NDI)-incorporated helical thienoacene was developed. The compound has high electron mobility (1.4 cm2 V-1 s-1) thanks to its two-dimensional π-π interaction assisted by the intermolecular C-HO hydrogen bonding of the NDI moieties. Moreover, its bow-shaped π-skeleton reduces molecular fluctuation and gives the compound a thermally stable solid phase, which enables us to fabricate thermally stable organic devices.

Low-Temperature Processed TiOx Electron Transport Layer for Efficient Planar Perovskite Solar Cells.

The most frequently used n-type electron transport layer (ETL) in high-efficiency perovskite solar cells (PSCs) is based on titanium oxide (TiO2) films, involving a high-temperature sintering (>450 °C) process. In this work, a dense, uniform, and pinhole-free compact titanium dioxide (TiOx) film was prepared via a facile chemical bath deposition process at a low temperature (80 °C), and was applied as a high-quality ETL for efficient planar PSCs. We tested and compared as-deposited substrates sintered at low temperatures (< 150 °C) and high temperatures (> 450 °C), as well as their corresponding photovoltaic properties. PSCs with a high-temperature treated TiO2 compact layer (CL) exhibited power conversion efficiencies (PCEs) as high as 15.50%, which was close to those of PSCs with low-temperature treated TiOx (14.51%). This indicates that low-temperature treated TiOx can be a potential ETL candidate for planar PSCs. In summary, this work reports on the fabrication of low-temperature processed PSCs, and can be of interest for the design and fabrication of future low-cost and flexible solar modules.

Metal Oxide Compact Electron Transport Layer Modification for Efficient and Stable Perovskite Solar Cells.

Perovskite solar cells (PSCs) have appeared as a promising design for next-generation thin-film photovoltaics because of their cost-efficient fabrication processes and excellent optoelectronic properties. However, PSCs containing a metal oxide compact layer (CL) suffer from poor long-term stability and performance. The quality of the underlying substrate strongly influences the growth of the perovskite layer. In turn, the perovskite film quality directly affects the efficiency and stability of the resultant PSCs. Thus, substrate modification with metal oxide CLs to produce highly efficient and stable PSCs has drawn attention. In this review, metal oxide-based electron transport layers (ETLs) used in PSCs and their systemic modification are reviewed. The roles of ETLs in the design and fabrication of efficient and stable PSCs are also discussed. This review will guide the further development of perovskite films with larger grains, higher crystallinity, and more homogeneous morphology, which correlate to higher stable PSC performance. The challenges and future research directions for PSCs containing compact ETLs are also described with the goal of improving their sustainability to reach new heights of clean energy production.

Knowledge and practices of exclusive breastfeeding among mothers in rural areas of Rajshahi district in Bangladesh: A community clinic based study.

BACKGROUND: World Health Organization (WHO) suggests that exclusive breastfeeding (EBF) is the best nutrition for the neonate. Still, it remains a big challenge to establish EBF not only in Bangladesh but also in any developing countries. OBJECTIVE: The aim of this study was to determine the level of knowledge and practices on EBF and its relationship between different socioeconomic and demographic factors among mothers having at least one child of aged 6-12 months in the rural area of Rajshahi District, Bangladesh. METHODOLOGY: A community clinic (CC) based study has been conducted by using semi-structured questionnaire. A total of 513 mothers having at least one child aged 6-12 months from 32 different CC in the rural area of Rajshahi District, Bangladesh during September to December 2015. A composite index, chi-square test, and logistic regression model were utilized in this study. RESULTS: The prevalence of knowledge and practices on EBF were 34.5% and 27.9% among mothers having at least one child aged 6-12 months. From the analyses, mothers age of ≥21 years were (adjusted odds ratio (AOR) = 13.840, 95% CI: 7.394-25.904; p<0.001) times more likely to have knowledge on EBF and (AOR = 0.084, 95% CI: 0.050-0.143; p<0.05) times less likely to have practices of EBF compared to mother's age ≤20 years. Service holders mothers were (AOR = 9.992, 95% CI: 4.485-22.260, p<0.05) times more likely to have practices than that of house wife. Home delivery mothers was (AOR = 0.208, 95% CI: 0.111-0.389; p<0.05) times less likely to have practices of EBF than that of the hospital delivery mothers. Those mothers monthly family income ≥10,000 Bangladeshi taka (BDT) currency was (AOR = 0.092, 95% CI: 0.050-0.168, p<0.05) times less likely to have practices of EBF compared to their counterparts. CONCLUSIONS: This study was found poor knowledge and practices on EBF. This study suggested that education and EBF related intervention could play an important role to increase good knowledge and practices on EBF among mothers. Malnutrition will be decreased if EBF was widely established in Bangladesh.

Effect of Ginsenoside-Rh2 and Curcurbitacin-B on Cryptosporidium parvum in vitro.

Ginsenoside-Rh2 and cucurbitacin-B (CuB) are secondary metabolites of Ginseng (Panax ginseng) and Cucurbitaceae plants respectively. We assessed the anticryptosporidial activity of these two functional compounds in a cell culture model of cryptosporidiosis. The highest concentration of each compound that was not toxic to the host cells was used to assess the activity against C. parvum during infection/invasion and growth in HCT-8 cell monolayers. Monolayers were infected with pre-excysted C. parvum oocysts. Infected monolayers were incubated at 37 °C for 24 h and 48 h in the presence of different concentrations of each test compound. A growth resumption assay was performed by incubating infected monolayers in the presence of compounds for 24 h followed by a second 24-h incubation in the absence of compound. To screen for invasion inhibiting activity, freshly excysted C. parvum sporozoites were pre-treated with different concentrations of compounds prior to adding them to the cell monolayers. Paromomycin, a known inhibitor of C. parvum, and DMSO were used as positive and negative control, respectively. The level of infection was initially assessed using an immunofluorescent assay and quantified by real-time PCR. Both compounds were found to strongly inhibit C. parvum intracellular development in a dose-dependent manner. IC50 values of 25 µM for a 24 h development period and 5.52 µM after 48 h development were measured for Rh2, whereas for CuB an IC50 value of 0.169 µg/ml and 0.118 µg/ml were obtained for the same incubation periods. CuB also effectively inhibited resumption of growth, an activity that was not observed with Rh2. CuB was more effective at inhibiting excystation and/or host cell invasion, indicating that this compound also targets extracellular stages of the parasite.